Welcome to the official website of Foshan Rhino Fine Chemical Co., Ltd.

0757-83830753  0757-83832736

Service hotline:

HOT key words:

Glass
Frosted
polishing
Concave etchants
Ice sculpture glass / concave glass
2015/3/19 0:00:00

Concave glass / ice-carved glass is a patterned glass with a concave-convex feeling and a frosty ice-like texture on the concave surface. Its beautiful appearance, vivid and lively patterns, can be designed according to the user's use of concave and convex patterns, thereby expanding its scope of use.


Process method and characteristics:


      Screen frosted glass ("ice-carved glass" directly produced by glossy glass), or engraving the etching pattern with a protective glass film, soak it in the concave etching solution for 20 to 50 minutes, remove and clean Get the finished product clean. The processed glass products produce bright and full three-dimensional ice-cold lines, which have special artistic effects that cannot be achieved by ordinary engraving methods.


Process equipment diagram:


All water tanks and piping materials require PVC materials, of which PVC boards require a thickness of 10-12mm.

Mechanical pumps require acid-resistant magnetic pumps.

The entire equipment is required to be as tightly sealed as possible.

Size and specifications can be customized according to customer requirements.

Dilute according to the weight ratio of concave Mongolian ice-etching etchant: water = 1: 1, stir well, cover the prepared medicinal solution and allow it to mature naturally at room temperature for 4 to 5 hours. The immersion time of the glass in the new compounding water is 20-50 minutes. The length of the immersion time has a great impact on the depth of the etching and the fullness of the ice edges. If the time is long, the etching is deep and the ice edges are thick. Otherwise, it is shallow and delicate. The glass effect is required to determine the soaking time.


After using the medicine for a period of time, the concentration will decrease and the etching depth is not enough. The immersion time can be appropriately extended. If the effect is not obvious, the etchant must be considered.

After using the medicine for a period of time, some white precipitates should be cleaned regularly to avoid affecting the ice edge effect. If the glass ice edge produces white edges and the ice edge effect is not obvious, add a small amount of tap water to stir the impurities in the liquid medicine. , And then add an etchant.

The addition method is to add an etchant stock solution at 10% of the total amount of the chemical solution, stir it and allow it to mature at room temperature for about 2 hours.

Seal the potion as much as possible during use to reduce the volatilization of the potion.

Operators must wear acid-resistant rubber gloves to avoid direct contact with the skin.

The operation site should be ventilated, and the operation process should be sealed as much as possible to prevent the volatilization of the medicine from affecting the surrounding environment.

The glass to be etched is wiped with a 5% hydrofluoric acid aqueous solution (1㎏hydrofluoric acid + 9㎏water), and then rinsed with tap water.

The small glass test effect is applied before production to determine the concentration of the chemical solution, the etching depth and the etching time, and then the product is produced.

When soaking, the etched side of the glass must be placed statically with the distance between 1 and 1.5 mm. Avoid placing air bubbles when placing the glass, otherwise it will affect the ice edge effect. For mass production, a lamination method can be used.

When stopping production, the potion should be completely sealed to maintain the effect.


About

Rhino Fine Chemical Co., Ltd.

Fax:86-0757-83811835

Email:[email protected]

Add:Foshan City, Guangdong Province, Foshan City, Guangdong Province Ganggang Road High-tech Development Zone

Contact hotline

86-0757-83830753

86-0757-83832736

Follow us on WeChat

Contact

Quick Navigation

Foshan Rhino Fine Chemical Co., Ltd.

Tell:86-0757-83832736

Fax:86-0757-83811835

Email:[email protected]

Add:High-tech Development Zone, Ganggang Road, Foshan City, Guangdong Province

COPYRIGHT © 2019 Foshan Rhino Fine Chemical Co., Ltd.  ALL RIGHTS RESERVED

Technical Support: Fengsoft Network

Ice sculpture glass / concave glass
2015/3/19 0:00:00

Concave glass / ice-carved glass is a patterned glass with a concave-convex feeling and a frosty ice-like texture on the concave surface. Its beautiful appearance, vivid and lively patterns, can be designed according to the user's use of concave and convex patterns, thereby expanding its scope of use.


Process method and characteristics:


      Screen frosted glass ("ice-carved glass" directly produced by glossy glass), or engraving the etching pattern with a protective glass film, soak it in the concave etching solution for 20 to 50 minutes, remove and clean Get the finished product clean. The processed glass products produce bright and full three-dimensional ice-cold lines, which have special artistic effects that cannot be achieved by ordinary engraving methods.


Process equipment diagram:


All water tanks and piping materials require PVC materials, of which PVC boards require a thickness of 10-12mm.

Mechanical pumps require acid-resistant magnetic pumps.

The entire equipment is required to be as tightly sealed as possible.

Size and specifications can be customized according to customer requirements.

Dilute according to the weight ratio of concave Mongolian ice-etching etchant: water = 1: 1, stir well, cover the prepared medicinal solution and allow it to mature naturally at room temperature for 4 to 5 hours. The immersion time of the glass in the new compounding water is 20-50 minutes. The length of the immersion time has a great impact on the depth of the etching and the fullness of the ice edges. If the time is long, the etching is deep and the ice edges are thick. Otherwise, it is shallow and delicate. The glass effect is required to determine the soaking time.


After using the medicine for a period of time, the concentration will decrease and the etching depth is not enough. The immersion time can be appropriately extended. If the effect is not obvious, the etchant must be considered.

After using the medicine for a period of time, some white precipitates should be cleaned regularly to avoid affecting the ice edge effect. If the glass ice edge produces white edges and the ice edge effect is not obvious, add a small amount of tap water to stir the impurities in the liquid medicine. , And then add an etchant.

The addition method is to add an etchant stock solution at 10% of the total amount of the chemical solution, stir it and allow it to mature at room temperature for about 2 hours.

Seal the potion as much as possible during use to reduce the volatilization of the potion.

Operators must wear acid-resistant rubber gloves to avoid direct contact with the skin.

The operation site should be ventilated, and the operation process should be sealed as much as possible to prevent the volatilization of the medicine from affecting the surrounding environment.

The glass to be etched is wiped with a 5% hydrofluoric acid aqueous solution (1㎏hydrofluoric acid + 9㎏water), and then rinsed with tap water.

The small glass test effect is applied before production to determine the concentration of the chemical solution, the etching depth and the etching time, and then the product is produced.

When soaking, the etched side of the glass must be placed statically with the distance between 1 and 1.5 mm. Avoid placing air bubbles when placing the glass, otherwise it will affect the ice edge effect. For mass production, a lamination method can be used.

When stopping production, the potion should be completely sealed to maintain the effect.


Foshan Rhino Fine Chemical Co., Ltd.

Add:High-tech Development Zone, Ganggang 

Road, Foshan City, Guangdong Province

Tel:86-0757-83832376

Fax:86-0757-83811835

Email:[email protected]

Follow us on WeChat

Copyright © Foshan Rhino Fine Chemical Co., Ltd.

   
 
X